RESUMEN

The interest in hydrogen is rapidly expanding because of rising greenhouse gas emissions and the depletion of fossil resources. The current work focuses on employing affordable Al alloys for hydrogen production and storage to identify the most efficient alloy that performs best in each situation. In the first part of this work, hydrogen was generated from water electrolysis. The Al alloys that are being examined as electrodes in a water electrolyzer are 1050-T0, 5052-T0, 6061-T0, 6061-T6, 7075-T0, 7075-T6, and 7075-T7. The flow rate of hydrogen produced, energy consumption, and electrolyzer efficiency were measured at a constant voltage of 9 volts to identify the Al alloy that produces a greater hydrogen flow rate at higher process efficiency. The influence of the electrode surface area and water electrolysis temperature were also studied. The second part of this study examines these Al alloys' resistance to hydrogen embrittlement for applications involving compressed hydrogen gas storage, whether they are utilized as the primary vessel in Type 1 pressure vessels or as liners in Type 2 or Type 3 pressure vessels. Al alloys underwent electrochemical charging by hydrogen and Charpy impact testing, after which a scanning electron microscope (SEM) was used to investigate the fracture surfaces of both uncharged and H-charged specimens. The structural constituents of the studied alloys were examined using X-ray diffraction analysis and were correlated to the alloys' performance. Sensitivity analysis revealed that the water electrolysis temperature, electrode surface area, and electrode material type ranked from the highest to lowest in terms of their influence on improving the efficiency of the hydrogen production process. The 6061-T0 Al alloy demonstrated the best performance in both hydrogen production and storage applications at a reasonable material cost.

RESUMEN

Purpose: The purpose of this study is to investigate how smartphone addiction and self-regulation failure influence students' academic life satisfaction considering the impacts of students' mind wandering and cognitive failures. It also sought to look at how students' minds wander, and cognitive failures are affected by smartphone addiction and self-regulation failure among university students. Methods: The WarpPLS-SEM software was used to analyze the research data retrieved from a sample of 950 undergraduate students from universities in Egypt and the Kingdom of Saudi Arabia (KSA). Results: In both countries, the findings revealed that students' smartphone addiction and self-regulation failures negatively affect students' academic life satisfaction and positively affect students' mind wandering and cognitive failures. Additionally, smartphone addiction is positively related to failures of students' self-regulation. Besides the negative influences of students' cognitive failures on their academic life satisfaction, cognitive failures mediated negatively the relationship between mind wandering and students' academic life satisfaction. Finally, students' mind wandering mediated the relationship between smartphone addiction, self-regulation failure, and academic life satisfaction. Discussion: The study introduces fresh insights into the study variables that can be used to expand the literature on academic life satisfaction. The study provides theoretical and practical contributions to students, educators, and policymakers of education.

RESUMEN

Due to its exceptional electrical and thermal conductivity, pure copper is frequently employed in industry as the base metal for thermal management and electromagnetic applications. The growing need for complicated and efficient motor designs has recently accelerated the development of copper additive manufacturing (AM). The present work aims to improve the power density of the copper laser powder bed fusion (Cu-LPBF) coil by increasing the slot-filling factor (SFF) and the electrical conductivity. Firstly, the dimensional limitation of Cu-LPBF fabricated parts was identified. Sample contouring and adjusting beam offset associated with optimum scan track morphology upgraded the minimum feature spacing to 80 µm. Accordingly, the printed winding's slot-filling factor increased to 79% for square wire and 63% for round wire. A maximum electrical conductivity of 87% (IACS) was achieved by heat treatment (HT). The electrical impedance of full-size Cu-LPBF coils, newly reported in this study, was measured and compared with solid wire. It can reflect the performance of Cu-LPBF coils (power factor) in high-frequency applications. Furthermore, surface quality benefited from either sample contouring and HT, where the side surface roughness was lowered by 45% and an additional reduction of 25% after HT.

RESUMEN

This study proposes a bioinspired exotendon routing configuration for a tendon-based mechanism to provide finger flexion and extension that utilizes a single motor to reduce the complexity of the system. The configuration was primarily inspired by the extrinsic muscle-tendon units of the human musculoskeletal system. The function of the intrinsic muscle-tendon units was partially compensated by adding a minor modification to the configuration of the extrinsic units. The finger kinematics produced by this solution during flexion and extension were experimentally evaluated on an artificial finger and compared to that obtained using the traditional mechanism, where one exotendon was inserted at the distal phalanx. The experiments were conducted on nine healthy subjects who wore a soft exoskeleton glove equipped with the novel tendon mechanism. Contrary to the traditional approach, the proposed mechanism successfully prevented the hyperextension of the distal interphalangeal (DIP) and the metacarpophalangeal (MCP) joints. During flexion, the DIP joint angles produced by the novel mechanism were smaller than the angles generated by the traditional approach for the same proximal interphalangeal (PIP) joint angles. This provided a flexion trajectory closer to the voluntary flexion motion and avoided straining the interphalangeal coupling between the DIP and PIP joints. Finally, the proposed solution generated similar trajectories when applied to a stiff artificial finger (simulating spasticity). The results, therefore, demonstrate that the proposed approach is indeed an effective solution for the envisioned soft hand exoskeleton system.

Asunto(s)

RESUMEN

This paper describes the development of a human gait activity recognition system. A multi-sensor recognition system, which has been developed for this purpose, was reduced to a single sensor-based recognition system. A sensor election method was devised based on the maximum relevance minimum redundancy feature selector to determine the sensor's optimum position regarding activity recognition. The election method proved that the thigh has the highest contribution to recognize walking, stairs and ramp ascending, and descending activities. A recognition algorithm (which depends mainly on features that are classified by random forest, and selected by a combined feature selector using the maximum relevance minimum redundancy and genetic algorithm) has been modified to compensate the degradation that occurs in the prediction accuracy due to the reduction in the number of sensors. The first modification was implementing a double layer classifier in order to discriminate between the interfered activities. The second modification was adding physical features to the features dictionary used. These modifications succeeded to improve the prediction accuracy to allow a single sensor recognition system to behave in the same manner as a multi-sensor activity recognition system.

Asunto(s)

RESUMEN

The process-structure-property relationships of copper laser powder bed fusion (L-PBF)-produced parts made of high purity copper powder (99.9 wt %) are examined in this work. A nominal laser beam diameter of 100 µm with a continuous wavelength of 1080 nm was employed. A wide range of process parameters was considered in this study, including five levels of laser power in the range of 200 to 370 W, nine levels of scanning speed from 200 to 700 mm/s, six levels of hatch spacing from 50 to 150 µm, and two layer thickness values of 30 µm and 40 µm. The influence of preheating was also investigated. A maximum relative density of 96% was obtained at a laser power of 370 W, scanning speed of 500 mm/s, and hatch spacing of 100 µm. The results illustrated the significant influence of some parameters such as laser power and hatch spacing on the part quality. In addition, surface integrity was evaluated by surface roughness measurements, where the optimum Ra was measured at 8 µm ± 0.5 µm. X-ray photoelectron spectroscopy (XPS) and energy-dispersive X-ray spectroscopy (EDX) were performed on the as-built samples to assess the impact of impurities on the L-PBF part characteristics. The highest electrical conductivity recorded for the optimum density-low contaminated coils was 81% IACS.